The depth collar looks like a nut that is directly connected to the bit. The little collar, which allows the bit to stop when it reaches the Kreg clamp, has a small window within it so that you can see the numbers beneath. How Do I Adjust the Kreg Jig Collar?Īs mentioned before, this is referred to as the easy-set drill bit because it is so simple to set the collar. Remember, even a slight 1/8-inch mix-up can make a bench uneven or keep a cabinet from closing correctly. This ensures that human error will not make an impact on the rest of your holes and cuts. Oxiclean: Which is Best?Ī friendly reminder: always measure twice when working with wood. The sizes marked on the bit are ½ inch, ¾ inch, 1 ¼ inch, and 1 ½ inch. Older models have the setting built right into the clamp part, which is where you’ll set the collar. Depending on the age or type of your Kreg jig, it may or may not have the depth markings on the actual bit. Instead, you will set your drill bit to the thickness of the wood. There is no hard rule to what you must set your Kreg jig when working on a project. The Kreg self-tapping screws are resistant to splitting the wood. You also want to be sure to not use wood screws (which can cause the wood to split when using pocket holes). If you do not use the Kreg brand, be sure it is a reputable brand. These self-tapping screws pull the two pieces of wood together to ensure a tight fit. The Kreg jig kit includes the screwdriver bit that will fit right into these square-headed screws. Kreg recommends using Kreg’s self-tapping screws, which have a square head. The Kreg jig has three holes, which provides an easy measurement for putting two holes in the wood at the perfect spacing.
You’ll guide the drill bit into the steel-reinforced guide, which creates the hole at the exact depth and angle that will work for the pocket hole. Clamp the tool to the wood, then attach the bit to the drill, and get the hole drilled. It’s so simple that Kreg refers to it as the “easy-set drill bit.” The collar of the jig has a window that will be moved to the placement of the depth for the drill. To use this tool, set the collar depth to the depth of the wood you are using.
#KREG DEPTH GAUGE SET PROFESSIONAL#
This makes the project even more professional and clean. This drill bit is fantastic because it is built to create a hole with three parts: the tunnel for the bit and screwdriver neck, the flat end for the head of the screw to sit on, and the pilot hole for the screw thread. With the Kreg jig drill bit and pocket holes, you don’t even need to use glue since the screws create such a strong bond. With a biscuit or dowl joint, you’ll need to cut a slat into the wood, insert the biscuit or dowl, glue it into place, clamp the two pieces of wood together, then wait for it to dry. Many woodworkers love the pocket hole joints because it removes the necessity for biscuit and dowl joints. The best part of this jig is that it allows you to drill a hole into a sturdier part of the wood because the ends of the wood are weaker and can split easily. This is a clamp-like device that holds a piece of wood at a certain height so that you can drill a hole at an angle to hide the nails and screws. This particular jig is created and sold by the Kreg company.
#KREG DEPTH GAUGE SET HOW TO#
In this article, we’ll discuss what a Kreg jig is, how to use it, and how to adjust the collar. There are a few great reasons for using a Kreg jig in your woodworking project. Knowing how to use a Kreg jig is essential when you’re a woodworker or beginner. It is also an excellent tool for beginners because it is quite simple to use. It is a valuable tool for any woodworker, and one of the more well-known secrets of the trade. At the same time, it makes very strong joints between the wood pieces. The Kreg jig is a handy tool that will help you to hide the nails and screws in your woodworking projects. That fancy little tool was called the jig, and more than likely, it was a Kreg jig. To me, it always seemed a fun trick to hide the hardware that he needed to build. He loved to build, so why not support that habit by supplementing the cost of the tools he purchased for his projects? One of the tools I loved to check out when I was in his workshop off of the garage was this thing that created angled holes. We often told him that he should sell his creations at festivals for extra money. My grandpa was a woodworker like no one would believe. Pinterest Facebook Messenger Twitter Reddit
0 kommentar(er)
